![]() Easy to use interface: WOL application has a simple and user-friendly interface that makes it easy to use for both novice and expert users.Ģ. WOL application has many features that make it a great tool for remote management, such as:ġ. WOL application can be downloaded and installed on mobile devices such as smartphones or tablets, which enables the user to control the target device remotely. It is an application that uses the network interface card of the computer to send a magic packet to the target device to wake it up from sleep mode or hibernation. e1000e 0000:00:1f.6 eno1: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Txĥ.25"/1.2 MB floppy services are supported (int 13h)ģ.5"/720 kB floppy services are supported (int 13h)ģ.5"/2.Mobile Wake on LAN (WOL) app is a useful tool for remote system administrators who want to wake up computers from a distance. e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode e1000e: Intel(R) PRO/1000 Network Driver Subsystem: Lenovo Ethernet Connection (2) I219-LM Supported link modes: 10baseT/Half 10baseT/FullĪdvertised link modes: 10baseT/Half 10baseT/FullĠ0:1f.6 Ethernet controller : Intel Corporation Ethernet Connection (2) I219-LM (rev 31) Oct 18 23:10:52 pve systemd: wol.service: Succeeded. Oct 18 23:10:52 pve systemd: Started Wake-on-LAN for eno1. Main PID: 950 (code=exited, status=0/SUCCESS) ![]() Process: 955 ExecStop=/sbin/ethtool -s eno1 wol g (code=exited, status=0/SUCCESS) Process: 950 ExecStart=/sbin/ethtool -s eno1 wol g (code=exited, status=0/SUCCESS) Loaded: loaded (/etc/systemd/system/wol.service enabled vendor preset: enabled)Īctive: inactive (dead) since Mon 23:10:52 CEST 1min 57s ago Sudo chmod 755 /etc/rc0.d/wol_poweroff.sh & sudo chmod 755 /etc/rc6.d/wol_poweroff.sh Created script to bring the ethernet interface down properly at shutdown :Ĭp /etc/rc6.d/wol_poweroff.sh /etc/ rc0.d/wol_poweroff.shįinally changed permissions to make it executable: I tried sending packets to the combination of host's MAC and IP (as well as broadcast to 255.255.255.255), ports 7,9,4343,4000,etc.When the machine is powered off, and I send magic packets using apps like "wol" (from a windows host), an android app (landroid), I understand that they are reaching the NIC as I can see the ethernet port flashing, but the machine doesn't boot.When the machine is powered on, I successfully tested receiving magic packets using netcat.I also created a systemd service " wol.service", to also set the eno1 interface's wol to "g", using ethtool (see #3 below).Created script to bring the ethernet interface eno1 down properly at shutdown, based on this bug (see #2 below).Updated cat /etc/network/interfaces so that at every boot, it sets the vmbr0 interface's wol to "g", using ethtool (see #1 below).The NIC supports WoL and is (/was already correctly) enabled and set to "g". ![]() ![]() The BIOS (is up-to-date) supports WoL and is enabled.At this point I am not sure if it is a configuration issue or a BUG? I can't get Wake on Lan (WOL) to work with Proxmox, no matter what. I then installed Proxmox 7 (5.11.22-4-pve) on the same hardware. I was able to wake up the system from a "Hibernate" or "Sleep" mode by sending a magic packet from another windows host. disable "reduce speed on power down") and the UEFI BIOS to make it work. I had to make some changes in the adapter settings (eg. I confirmed that Wake On Lan works with Windows 10 Pr o on a Lenovo ThinkStation P310 with onboard Intel I219-LM GB Ethernet controller. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |